Roof Flashing Repair in Vestavia Hills, AL: Stop Leaks at the Transitions Before They Reach Inside
Most roof leaks don't start in the shingles. They start where the roof meets a wall, a chimney, or a vent, and where flashing has failed or was never done right. Fortress Roofing finds the real problem and fixes it. Call (205) 855-7663 for a free inspection.
24/7 Emergency Service | Trusted Service from Start to Finish | Locally Owned & Operated
You've had the same ceiling stain for three rainy seasons, and every time someone patches it, it comes back. The problem isn't where the water shows up. It's where the water gets in. Roof flashing is the metal that seals every joint and transition on a roof, and when it fails, water finds a way through. Fortress Roofing finds the failed flashing and fixes it for good.
Call (205) 855-7663.
When You Need Roof Flashing Repair
You need flashing repair when water stains appear near a wall, chimney, vent, or roof valley and no amount of patching makes them go away. Lifting or separated metal and visible rust on the flashing are clear signs. So is caulk that's dried and cracked along a joint. Flashing originally installed as a single bent piece rather than stepped and correctly layered at transitions is also a frequent source of ongoing leaks that caulk can't permanently seal.
Our Roof Flashing Repair Process
We start by getting on the roof and tracing the water to its actual entry point, which is often different from where it appears inside. According to the U.S. Department of Energy, even properly installed exterior cladding systems can experience some moisture penetration, which is why the flashing and sealing at every transition has to be correct. We remove the failed flashing and assess the underlying structure before installing new flashing that's correctly lapped and sealed. We confirm the repair before we leave and don't patch over the problem.
Waterproofing Services Cost in Vestavia Hills
Cost depends on where the failure is, how much flashing needs to be replaced, and whether any underlying damage needs attention before the new flashing goes in. A simple reseal on a small section costs less than a full reflash of a chimney or wall transition. We inspect first and give a written estimate so you know the scope and cost before any work is approved.
Why Choose Us
Fortress Roofing diagnoses flashing failures correctly. We don't caulk over flashing that needs to be replaced, and we don't guess at the entry point when we can climb up and find it. We're locally owned and operated. Our team is licensed and insured, and we hold CertainTeed's ShingleMaster certification. Customers consistently describe us as thorough and honest, with repairs that actually hold.
Frequently Asked Questions
-
Roof flashing is metal sheeting installed at every point where the roof surface meets another element: walls, chimneys, vents, valleys, and skylights. Its job is to seal those joints and direct water away from the openings. Flashing is one of the most important details in any roof system and one of the most common sources of leaks when it fails or was never installed correctly.
-
If water appears inside near a transition point, such as where a wall meets the roofline or near a chimney or vent, the cause is almost always flashing. If water appears in the middle of a room with no penetration above it, the shingles may be the issue. A professional inspection identifies the actual entry point rather than guessing from below.
-
Caulk applied over failed flashing is a temporary measure, not a fix. Caulk degrades in a few months to a few years in outdoor exposure, especially in Alabama's heat. A proper repair involves removing the failed metal, correcting the installation, and installing new material correctly. Caulk may be used as a finishing sealant on top of correct flashing, but it's never a substitute for it.
-
Correctly installed metal flashing should last for decades and can outlast the shingles above it. Lifespan depends on the material, the installation quality, and the exposure conditions. Aluminum and galvanized steel are the most common materials for residential flashing. Copper lasts the longest. We use materials appropriate for the repair and install them to hold, not to need revisiting next season.
-
Sometimes, but not always. If the repair requires removing shingles to access and correctly reset the flashing, those shingles may need to be replaced. If they're in good condition and lift cleanly, they can often be reset. We assess the condition of the surrounding shingles and tell you what's needed before any decision is made.
A recurring leak is telling you something about your flashing, not your shingles.
Call (205) 855-7663 or request a free inspection to find out exactly where it's getting in.